repairing typo and update some figures

docs/helios64/boot_mode.md

@@ -1,29 +0,0 @@
-Helios64 supports at least **3 (TBD)** boot modes that can be chosen by using the jumper configuration.
-
-The default Boot device order for Helios64 is the SPI Flash Memory, eMMC, then micro-SD Card.
-The SoC will access this order sequentially to find the bootloader in all possible storage medium.
-To change the boot order if the bootloader are present in all possible volatile storage, we can use the combination of P10 and P11 jumpers.
-(Please see above figure for the connector/interface list.)
-Following jumper are available in the Helios64 board to configure the boot modes:
-
-- P11 jumper can be used disable SPI Flash, when this jumper is shorted/close it means disable boot from the SPI Flash, and the board will search the next boot device (which is eMMC). 
-- P10 jumper is available to disable eMMC boot, when this jumper is closed Helios64 wil skip looking for bootloader from the eMMC and will continue with the micro-SD card,
-
-So you can select to search for bootloader starting from the SPI Flash Storage, eMMC, untill micro-SD card.
-Following table may simplified boot ordering by jumper config by assuming the bootloaders are present in every storage device:
-
-![Boot modes](/helios64/img/bootmode/bootmode_jumper.png)
-
-P11 State|P10 State|Boot Order|Notes
------|---------------|--------------|-------
-0|0|SPI Flash|-
-1|0|eMMC|-
-1|1|micro-SD Card|-
-
-!!! note
-	Please note, in case of bootloader is not present in the storage devices. The SoC will search to the next possible boot device.
-
-
-All the ready-to-use images we provide are for the **SD Card** boot mode.
-
-Please refer to [U-boot](/helios4/uboot) section to know how to use the other modes.

docs/helios64/install-1.md

@@ -1,4 +1,4 @@
-## **Step 1** - Download Helios4 OS image
+## **Step 1** - Download Helios64 OS image
 
 Before we start, you will need to download the Armbian Image for Helios64 build.
 

docs/helios64/jumper.md

@@ -1,9 +1,36 @@
 ## Boot Mode (P10 & P11) 
 
-![Bootmode location](/helios64/img/jumper/p11-12-jumper.png)
 
-Refer to [Boot Mode](/helios64/boot_mode)
+Helios64 supports at least **3 (TBD)** boot modes that can be chosen by using the jumper configuration.
 
+The default Boot device order for Helios64 is the SPI Flash Memory, eMMC, then micro-SD Card.
+The SoC will access this order sequentially to find the bootloader in all possible storage medium.
+To change the boot order if the bootloader are present in all possible volatile storage, we can use the combination of P10 and P11 jumpers.
+(Please see above figure for the connector/interface list.)
+
+![Bootmode location](/helios64/img/jumper/p11-jumper.png)
+
+Following jumper are available in the Helios64 board to configure the boot modes:
+
+- P11 jumper can be used disable SPI Flash, when this jumper is shorted/close it means disable boot from the SPI Flash, and the board will search the next boot device (which is eMMC). 
+- P10 jumper is available to disable eMMC boot, when this jumper is closed Helios64 wil skip looking for bootloader from the eMMC and will continue with the micro-SD card,
+
+So you can select to search for bootloader starting from the SPI Flash Storage, eMMC, untill micro-SD card.
+Following table may simplified boot ordering by jumper config by assuming the bootloaders are present in every storage device:
+
+P11 State|P10 State|Boot Order|Notes
+-----|---------------|--------------|-------
+0|0|SPI Flash|-
+1|0|eMMC|-
+1|1|micro-SD Card|-
+
+!!! note
+	Please note, in case of bootloader is not present in the storage devices. The SoC will search to the next possible boot device.
+
+
+All the ready-to-use images we provide are for the **SD Card** boot mode.
+
+Please refer to [U-boot](/helios4/uboot) section to know how to use the other modes.
 
 ## HS Select (P13)
 
@@ -16,6 +43,8 @@ When this jumper closed the High Speed USB (USB 2.0) connection to the SoC will
 
 ## Power Supply Priority Jumper (P14 & P15)
 
+![P14 location](/helios64/img/jumper/p14-jumper.png)
+
 | P15 | P14 | Description |
 |-----|-----|-------------|
 | Open  | Open  | O-Ring Connection |
@@ -31,7 +60,9 @@ Production usage only.
 
 ## eFuse Power Enable (P9)
 
+![P9 location](/helios64/img/jumper/p9-jumper.png)
+
 Short this jumper using tweezer to burn the efuse data on maskrom mode.
 
 !!! warning
-	Wrong efuse data can brick Helios64. Do NOT short this jumper on normal use! 
+	Wrong efuse data can brick Helios64. Do NOT short this jumper on normal use! 

docs/helios64/m2.md

@@ -18,7 +18,7 @@ The location of the M.2 socket is shown in below figure:
 
 ## Size
 
-The maximum size of supported M.2 device is the 228 size. 
+The maximum size of supported M.2 device is the 2280 size. 
 
 ## Notes related to M.2 Card
 The M.2 devices installed in Helios64 is configured as sharing devices with SATA Port 1.

docs/helios64/uext.md

@@ -19,7 +19,7 @@ Please find this location of UEXT header:
 
 The pinout of the above P2 header is decribed by following figures:
 
-![P2 Pinout](/helios64/img/hardware/UEXT_pinout.png)
+![P2 Pinout](/helios64/img/hardware/UEXT_pinout_full.png)
 
 Below is the detailed description of UEXT header pinout:
 

docs/helios64/usb.md

@@ -4,7 +4,7 @@
 
 There are three types of USB controller available on RK3399. Each type has two controller so total USB controllers is 6.
 
-### Generic OHCI USB 1.1 Controller
+## Generic OHCI USB 1.1 Controller
 There are two controller of this type. This controller is Host only controller that is compatible with USB 1.1.
 Supported speed:
 
@@ -12,7 +12,7 @@ Supported speed:
 
 - Low Speed (1.5 Mbps)
 
-### Generic EHCI USB 2.0 Controller
+## Generic EHCI USB 2.0 Controller
 There are two controller of this type. This controller is Host only controller that is compatible with USB 2.0. The controller shared port with 
 [Generic OHCI USB 1.1 Controller](#generic-ohci-usb-11-controller) therefore any USB 1.1 device connected to the port, will be automatically 
 routed to [Generic OHCI USB 1.1 Controller](#generic-ohci-usb-11-controller).
@@ -21,7 +21,7 @@ Supported speed:
 - High Speed (480 Mbps)
 
 
-### Synopsys DesignWare USB 3.0 Dual-Role Device Controller
+## Synopsys DesignWare USB 3.0 Dual-Role Device Controller
 There are two controller of this type. This controller support On-The-Go /Dual Role which mean it can be configured as Host and also Device.
 Supported speed:
 

mkdocs.yml

@@ -77,7 +77,6 @@ nav:
   - Hardware:
     - Overview : 'helios64/hardware.md'
     - Battery : 'helios64/battery.md'
-    - Boot Mode : 'helios64/boot_mode.md'
     - Button : 'helios64/button.md'
     - Front Panel (P3): 'helios64/front-panel.md'
     - GPIO (P5): 'helios64/gpio.md'